Category Archives: Tips and Technique

EQ Tips & Tricks for Pedal Steel

Ahhh…the pedal steel. Sometimes there’s nothing more delectable than the sound of a well-mixed, sonically pleasing pedal steel in a recording. Add some tasteful playing, good tonality, and a hip song, and listeners are in for a treat. But besides flavorful playing by a solid player, what can make the pedal steel sound even more wonderful on record? Equalize it.

Equalization involves boosting or cutting volume levels at certain frequencies to alter the sound of a signal. Different frequencies affect the sonic space of a recording in their own way, and influencing them with EQ can improve the sound of a recorded instrument or song. With a distinctive timbre and broad frequency range, the pedal steel can often benefit from some EQ in the pre or post-production stages.

EQing during Mixing

Let’s assume the pedal steel player, engineers, and producers did their best to capture a good sound out of the pedal steel during a session…they may have had ideas on what amps to use, mics, tones they were seeking, etc. (Or if recording one’s self at home, a pedal steel player may have similar ideas for capturing the instrument’s sounds.) After the pedal steel has been recorded, the mixing process will begin to look at how the pedal steel sounds by itself, how it sounds in relation to other instruments, and how it will sound in the overall recording. This is a good time to look at how EQ can affect the pedal steel’s sound.

IMG_3307

There are no set rules for mixing pedal steel or EQing it, so these EQ tips contain advice to help a person calibrate and experiment with sounds they want to achieve in the recording. Often, less is more with EQ or other effects, so I usually find myself using EQ as a way to compliment and enhance what already sounds good with the recorded signal. For instance, if the high frequencies of the pedal steel sound great already, then I won’t mess with them (if it ain’t broke, don’t fix it mentality). However, if the lower end frequencies of the pedal steel sound muddied, boomy, or weird, while the highs sound great, then EQing the low end can make the steel track sound much better – combine this with the already great sounding highs, and we now have a solidly pleasant pedal steel sound that we can move forward with.

EQ Tips & Tricks

After mixing pedal steel numerous times for recordings with bands, singer-songwriters, and solo playing, here are the most common and successful uses I have found for EQ on the pedal steel:

  • Cut between 300 and 400 Hz with a fairly wide Q – This is often a very boomy, muddy, and dense area of the frequency range that can hold a lot of unwanted energy and sound that a listener can live without. Cutting this area usually results in a cleaner steel sound, allowing the mids to sound clearer, and the highs to have more presence. Also, it will give the bass and drums more room to breathe and thrive in the lower end of the frequency spectrum – we don’t want to step on their toes too much, especially if the pedal steel is being utilized more for its higher frequencies in the recording.

Furthermore, if we are playing lower frequencies on our steel (C6 bass notes especially), cutting this 300-400 Hz range can help define and provide “oomph” to these lower notes, and give them more impact on the listener without bogging them down. I often cut the gain pretty aggressively on this adjustment…I’ve found myself cutting anywhere from 3 dB to 9 dB with a fairly wide Q. [Note: this cut works wonders when mixing a drum kit – it will usually clear up the sound of the overall drums in an amazing manner.]

  • Slightly boost 10 kHz and higher with a shelf – This will add more presence to the pedal steel, and allow the highs to “crystallize” and sparkle within the recording. The pedal steel is often known for its higher frequencies, and its ability to “cry” in the upper threshold of the sonic spectrum. This boost can magnify this characteristic of the pedal steel, and allow listeners to indulge in its highs. Don’t overdue it though: a 0.5 to 1.0 db boost is usually plenty with this shelf.
  • Cut 4 kHz with a sharp Q – I often find that when a recorded instrument sounds shrill or irritating in the mids to highs that it can really benefit from a 4K cut. The human ears are pretty sensitive around this frequency range; if a recording has too much going on in this frequency range, then it can often feel like someone is throwing a dart into your ear. That sounds pretty rough, and may be a little exaggerated, but it is often true. My guess is that if a person scrapes their nails on a chalkboard (are your ears hurting yet?), and it is recorded, this recording won’t sound nearly as bad if a 4K cut is added to it. Alright, you get the point.

But for real, with many recordings and recorded instruments, if there is some harshness in the mids to highs, it can often live in the 4 kHz area. This pertains to the pedal steel as well, so let’s fluff up this great sounding instrument and make it feel real comfortable to listeners’ ears by cutting 4K if there is some harshness. I do this with a fairly sharp Q, and usually cut between 1.0 dB to 3.5 dB depending on the severity. I use a sharp Q to be sure not to mess with other important harmonics, tones, or frequencies that are important to the overall sound of the instrument – I don’t want to step on any frequency’s toes if they are adding pleasantness to the sound, especially in the higher frequencies of the pedal steel.

  • Don’t give away your Grandma’s secret recipe, but boosting 20 kHz can really spice up the meal – So, you may be asking: “I thought humans can only hear sounds within the 20 Hz to 20,000 Hz range?” Well there is some truth to this, but that doesn’t mean sonic energy doesn’t live outside of this range…just ask dogs, many of them can hear well beyond 20,000 Hz. Well, besides that we want man’s best friend to enjoy the sound of our pedal steels, there is also another reason to boost here: it can really add some air, lucidity, and sparkle to the sound.

This boost is like adding presence to the sound, but at an even higher elevation, at a place where clouds mist into snow-capped peaks and angels wave huge feathers to provide a nice relaxing breeze for whomever finds themselves in this 20K and beyond oasis. OK, back to earth (can you tell I really like this EQ trick?). This tip was taught to me by a Grammy-winning mastering engineer, and I am forever grateful. It is very hard to hear the difference between before and after this boost, but it is there and with critical ears it can be found, just give it some time. I usually boost 0.5 dB here, and enjoy how fluffy it makes the instrument sound, especially since the pedal steel enjoys frolicking in the high frequencies.

IMG_3306

A/B Testing: Reap your Rewards

A great way to see/hear these EQ tips in action is to use the bypass button on your EQ plug-in, and A/B (compare before and after) the added equalization. For instance, take the 4K cut mentioned earlier…listen to the pedal steel as it originally sounded. Next, add in the cut on your EQ. Now take a listen…notice any difference? Maybe, maybe not…well go ahead and hit the bypass button on your plug-in to see what it sounded like without EQ again. Now add the EQ into it again by releasing the bypass button. Try to listen for any subtle changes in the sound of the instrument with and without the EQ.

It may take a few or several comparisons, but chances are you’ll notice some differences and whether or not they improve the sound. Try closing your eyes, if you’re having trouble hearing the differences. Or try clicking the bypass button with your eyes closed a random amount of times, then click it again, and see what sounds better to your ears…then once you have which one you think sounds better, open your eyes and see if it’s the one with EQ on it. This may help you narrow down whether or not the EQ is actually helping the overall sound.

These EQ tips are just suggestions if one isn’t completely happy with the sound they’re hearing with the recording…there are often times when the recorded signal sounds great already and will hold up beautifully on its own. However, experimenting with these tips can be a great way to learn the effect different frequencies can have on the ears. It can also be a great way to better understand the sound of the pedal steel, and how EQing it can affect it. Also, these EQ tricks can be used on amplifiers and EQ pedals at a gig, in the practice room, or on that snow-capped oasis land mentioned earlier. Enjoy the experimenting, and I hope you get closer to the sound you desire!


Check out these tonal personalities for sonic inspiration…

Cindy Cashdollar

Greg Leisz

Buddy Emmons

Lloyd Green

Blank Fretboard Diagram for E9 or C6 Necks

When practicing, it can be useful to have visual tools to use as aids. The following is a blank fretboard diagram for the E9 or C6 neck that can be used to create scale patterns, chord shapes, riffs, and more.

Feel free to print this out, and use a pencil/pen to mark in whatever you’d like!  Click on the image for an enlarged view, then the magnifying glass for a zoomed-in view.

PedalSteelBlankFretboardDiagram


Refer to the following posts for ideas on how to use this diagram…

C6 Note Chart

E9 Neck – Major Thirds and Perfect Fourths – 4th & 5th Strings

Bluesy Chord Voicings for the C6 Neck

C6 Neck – A Aeolian Scale – 8th String Root Position (Vertical)

Right Hand Technique: Using the Ring Finger as an Anchor

Having a comfortable, confident right hand picking technique can go a long ways for a pedal steel player. Right hand picking and string blocking are perhaps the most elusive techniques to new and seasoned players alike. However, by using the ring finger as an anchor, a player can overcome many picking obstacles and become triumphant in the choppy seas of right hand technique.

Most players use a thumb pick, and fingerpicks for the index and middle fingers, leaving the ring and pinky fingers free to roam. Many players extend their pinky out when picking, while others tuck it under their ring finger…there is no right or wrong way; whatever is comfortable and works best for the player. This leaves the ring finger: and using this finger as a positional anchor can tie everything together for the right hand.

Check out the photo gallery at the bottom of the page to see photos of the ring finger anchor in action.

Pedal Steel Pick Art - Smiley Face

What is meant by positional anchor, when referring to the ring finger? This means resting it in between two strings, or on top of a string, so that the picking fingers below are in the correct position to pick their intended strings in a comfortable manner.

Accurately switching between string grips, and picking the intended notes can be challenging. However, if we train our ring finger to land on top of the strings we want it to, while keeping the thumb, index, and middle fingers in a consistent position relative to the ring finger, we can confidently attack the strings with accuracy.

RingAnchor2
Here the ring finger rests on string 3, while the thumb and middle fingers pick strings 5 & 4.

For example, if we are going to play strings 6 & 5 with our index and middle fingers, then resting the ring finger on string 4 (and it may touch string 3 too – it can comfortably rest between strings 3 & 4) can provide a foundation for the picking fingers. These fingers should now be in the proper position and angle, huddled over the strings ready to pick, dampen, or release from the strings. Basically, they will be in a position to attack the strings, mute them (pick blocking), or release from them after they’ve been picked or muted.

If a player wants to do the same thing, but on a different string grouping, then it is just a matter of shifting the foundation forward or backward to different string numbers. For instance, if a player wants to pick strings 6, 5, & 4 on the E9 neck (a classic grip indeed), then they can rest their ring finger on the 3rd string. Again, resting it on this 3rd string implies that it may touch the 2nd string too, or can be thought of as resting in between the 3rd and 2nd strings.

RingAnchor7
Using the ring finger as an anchor can really allow the thumb, index, and middle fingers to relax when picking. In this picture, the thumb and middle finger are picking adjacent strings, while still allowing the index finger to relax comfortably as well. Notice how similar the index and middle fingers are in stature.

A major benefit of the ring finger anchor is that it will mute whatever string(s) it rests upon, providing aid to the blocking process. If the pinky finger is extended as well, then most of the higher strings will be blocked. For blocking, this leaves the player free to focus on properly muting the lower strings that aren’t being picked: often by using the palm, or the side of the hand.

Buddy Emmons was an advocate of using the ring finger to mute string(s): knowing that it could rest on the string, and mute the string at the same time.

If a player can train the ring finger to land in the correct spot each time, and train the other fingers to remain in the same comfortable position/shape relative to the ring finger, then they have a reliable system for placing the fingers in any position they want to pick and block the strings. There is more consistency, and less trial-and-error for moving between picking positions and string groupings.

image1-8

There can be many advantages to using the ring finger as an anchor:

-It allows the overall hand to relax more, which can make it easier to pick comfortably, faster, and more accurately.

-It helps mute more strings for blocking.

-It allows the thumb, index, and middle fingers to position more consistently with each other…they will be more “tight-knit” as a group and will move and work better together. Better yet, they won’t roam as much from each other, and will be more accurate and consistent in picking their intended strings.

-It can help with speed picking, chord grips, and many other picking options.

-It can save time and energy when practicing right hand technique, and allow a player more time to focus on other aspects of playing like bar control, scale routines, or learning tunes.

So as a player embarks on the seas of pedal steel discovery, they should keep in mind that a strong anchor is always nice to have: to keep from drifting into the rough seas of abysmal right hand technique.

Photo Gallery of the Ring Finger Anchor (click to enlarge):


For more on right hand technique visit the following page:

Right Hand Blocking

Big Sounding Chords for the C6 Neck

There’s nothing like a nice, full, big-sounding chord that is played on the C6 neck:  Combine with sustain from the volume pedal, some reverb, and a touch of vibrato and you’ve got the ingredients for some killer chordal recipes.

Below is a diagram for some big sounding chords on the C6 neck…

C6Chords-BigSound-Root10thString
CLICK ON IMAGE FOR LARGER/PRINTABLE VIEW

These all have their root notes on the 10th string (7th string as well), allowing a player to move up and down the fretboard to change chords within a progression.  I have included the Nashville numbering system for these chords to help a player better understand how these chords relate to each other.

To pick these, I suggest using the thumb for the 10th string, and the index and middle fingers to grab notes on the other strings: better yet, hit the 10th string note first, then use the thumb to pick strings 7-5, and the index and middle fingers for strings 4&3.

Experiment with these chord voicings, and enjoy the benefits of the C6’s frequency range.  These voicings can sound like an organ or keyboard, and can really add some sizzle to a tune!

Happy Halloween!
Happy Halloween!

For more on C6 chord voicings, or how to pick these chords, visit these pages:

Bluesy Chord Voicings for the C6 Neck

Thumb Strum – Chordal Picking Technique

Thumb Strum – Chordal Picking Technique

This is one of my favorite picking techniques, and is wondrous on the C6 neck. Its main function is to use the thumb to quickly strum multiple notes and provide a thicker chordal sound. When done correctly, the group of notes should sound similar to a guitar player strumming a chord with their pick.

This technique is best utilized with a note played on top with the middle finger, or the middle and index fingers. The combination of the thumb and other fingers allows a large chord voicing that can really expand a player’s chord arsenal.

The thumb will begin on the lowest string, and then will pick the group of notes simultaneously by strumming forward. At the same time this done, the other finger(s) will pluck its appropriate note.

Here is a diagram that displays a few chord voicings on the C6 neck with this technique:

ThumbStrumChordPickingTechnique
CLICK ON DIAGRAM FOR LARGER/PRINTABLE VIEW

Further enjoy the benefits of this picking style by letting the thumb’s notes sustain, and using the middle finger and knee levers to add melodic texture for higher notes above this, in the same position. This concept can be a gateway into the world of chord-melodies on the pedal steel!


For more on picking and blocking, visit these pages…

How to Practice Right Hand Blocking on Pedal Steel Guitar

What is Right Hand Blocking on Pedal Steel Guitar?

Picking (or Right Hand Blocking) for Six-String Guitar Players

Practice Strategies

Learning how to play the pedal steel guitar can be fun, rewarding, and worthwhile. The process of learning, and the challenges involved with this intricate instrument, are part the journey. Using strategies that can make practicing more efficient and beneficial, a player can improve their playing with enjoyable outcomes.

Here are some practice strategies that I have found useful when learning this instrument:

Chunking

There is so much involved with learning to play music and an instrument that it can feel like climbing a mountain…but mountains are climbed one step at a time. The same idea can be applied to practicing pedal steel. Breaking down the material and techniques that need to be learned into “chunks” can provide more focus to attain important goals.

If a player’s goal is to spend a little time each day working on technique, scales, and tunes, then finding a good exercise to work on for each of these categories is important. There are multiple aspects of technique that are important to learn, plenty of scales, and thousands of tunes. It can feel overwhelming to think about how much there is to learn, so choosing one area out of each category to focus on for practice sessions can provide direction, focus, and the time necessary to truly learn: after all, the key to learning is repetition.

Practicing Pedal Steel and Rediscovering Songs

I recommend choosing an exercise for each category and working on it for a few weeks before moving on to the next goal. For technique, this may mean focusing on bar control by doing a 15 minute exercise centered around this each day. For scales, working on the major scale and the Mixolydian scale each practice session may be more beneficial than trying to learn every scale/mode at once. For tunes, working on the verse over and over again until you have it down may be more beneficial than noodling between every section without truly getting them down.

After three weeks of practicing one particular thing each day, a player will see significant gains in that area. This is a good time to move on to another exercise, and begin building a new foundation. These foundations can provide good leverage for climbing the pedal steel mountain.

Consistency

The more a player can successfully complete their playing objective (i.e. hitting a right note, or playing a lick accurately up-to-speed) the easier it will be to repeat this. So when practicing it is important to try to repeat successful results more often than unsuccessful ones.

If a player completes a picking exercise successfully three out of four times, then they are building a habit of playing it accurately more often than not. Doing this more and more often, until it can be done successfully 9 out of 10 times, will build consistency of success.

If they are only completing it successfully one out of five times, then they may find it beneficial to alter their practice routine so that more successes can be made more of the time. This may mean slowing the metronome down a bit until one can play it successfully more often, then speed it up slowly until the same can be done at the next speed.

image

Once a player can successfully repeat something over and over again accurately, it is a good time to move on to something more challenging and push for growth instead of being stagnant. If a player can’t repeat something successfully more often than not, then it is a good time to change some variables to make it easier to. After all, you have to crawl before you can walk.

Timing

It is important to practice smart, not harder. A player may be able to make just as many gains from practicing efficiently for 10 minutes, than inefficiently for 2 hours. During your practice session, ask yourself: am I focused enough right now to truly be productive on the task at hand? If not, is it because your fingers are tired, or are you distracted by your friend’s text messages, or maybe you’re hungry cause you haven’t eaten yet today?

Know your limits, and if you begin making more mistakes than earlier in the practice session, then it may be a good idea to take a break. (Mistakes are OK!, but just make sure you aren’t making more of them because your practice session has lost its steam.) When you notice you need a break, here are some things that can help refresh you: go for a walk, do a quick stretch, eat a granola bar, listen to a couple of inspiring songs, or maybe just take some deep breaths. Effective practice builds good playing habits, and getting in the habit of practicing effectively is making the best of both worlds.


Remember that practicing and learning requires making mistakes, so make the most of learning from them and have fun! Understanding how to practice effectively, and how to improve one’s playing, can be rewarding and can yield significant gains. Using these strategies can give a player more ideas on how to do this.

For more practice strategies click below:

Practicing Pedal Steel Guitar

Bluesy Chord Voicings for the C6 Neck

Everyone loves the sound of a nice, thick, warm-sounding chord voicing…whether they know it or not.  Luckily for us pedal steel players, the C6 neck can provide ample amounts of these chordal sounds.

The C6 neck, with its beefy low end – and intuitive, intervallic layout – is a perfect vehicle for voicing chords that can make ears tingle.  The 10th string rivals a bass guitar’s frequencies…and when combined with some higher end, it can really bring out a chord that sounds like a plethora of keyboard, bass, guitar, and pedal steel.  Not many instruments have the sonic and frequency capabilities of the pedal steel.

image

Below are three different voicings for a Dominant 7 chord, which can be used in many blues, jazz, and rock n’ roll settings.  They are best used interchangeably, and a player can quickly switch between the three to produce nice harmonic variety — the highest notes will provide some listening variety.  They are in the same position, so practicing/switching the grips is the key to playing these.  (Click on the diagrams for a larger image).

Voicing #1

C6-Dom7BluesChordVoicings-1

They are relatively straightforward: all have a constant use of the 10th string to provide our root note (these are for an F chord), and all of them use three fingers.  Not all of these voicings contain the b7th note of the chord, but they imply this type of tonality, and when played in a band or musical setting they are often enough to get this sound across to the listener.

Voicing #2

C6-Dom7BluesChordVoicings-2

If you are playing some blues in the key of F, then moving this position to the 10th fret can provide the IV7 chord, and playing it at the 12th fret can provide the V7 chord.  Experiment with these grips/voicings, between the three positions, for some hip chordal sounds!

Voicing #3

C6-Dom7BluesChordVoicings-3


Click below for more practice tips and ideas…

Practicing Pedal Steel

Buddy Emmons’ Characteristics: How They Can Improve your Playing

Updated on 9/27/17

Buddy Emmons has left a deep impression on the musical world, as well as the steel guitar community. He was an amazing player, with chops and ideas that we all wish we had. His playing seemed perfect, and it usually was. But he too was human, and we can all relate to that. Here are some characteristics of Buddy that we can all connect to, and use to improve our selves and our pedal steel playing.

Smile

Buddy Emmons had impeccable chops, incredible tone, and ingenuity when it came to the pedal steel guitar; add a smile and laugh to this, and you have “The Big E”. We all admire Buddy’s playing, and consider it to be nearly flawless, but he also made mistakes every once in awhile. That is how we learn and grow as people, and begin to push boundaries in a beneficial way: we make mistakes and learn from them. It seemed that whenever he did this (made a mistake), he accepted this and tried to shake it off quickly and move on: he did this by smiling or laughing at the mistake. To error is human, so when he made an error, he did something every human can enjoy: a good smile and laugh. He also did this when his playing was “on fire” too!

Try it sometime on the bandstand, or in the practice room. Look lively and excited once in a while, and your steel playing may just sound the same. There is current evidence in science that suggests if a person makes their body react in a certain way, it sends signals to the brain to act in the same way: for instance, if you make yourself smile, then your brain will sense this and make you feel happier. Seems like Buddy was onto something there.

Use Your Intuition

Buddy seemed to be an intuitive individual, as we can tell from many of his inventive contributions to the pedal steel guitar. He had a knack for following his instinct, or doing what felt right at that moment, many times with an improvisational approach. His intuitive addition and use of the strings D# and F# (strings 2 & 1) on the E9 neck is now a modern day staple of the 10-string E9 neck tuning. He came up with the three pedal configuration that we now consider standard on any E9 neck pedal steel. Also, did I mention the Emmons and Sho-Bud brand pedal steels that he helped develop, which are still sought after for their ingenious design, taste, and tone?

His intuition is also evident in his creative, improvisational approach to many of his studio sessions, and own personal work. Coming from a jazz background, and favoring the improvisational approach in this regard, Buddy liked to follow his instincts in the music too, and follow it wherever it took him. That’s one reason we love his playing; we never knew where it would take us.

To better follow your intuition at the pedal steel guitar, try not to play licks, songs, or riffs that you have memorized, and can already play over and over. Try to improvise. Step out onto the plank, and dive into the deep waters…try something new – you don’t know where it will take you, but that’s the beauty of it. It’s like life, sometimes you just have to improvise, and that can be the fun in it.

Be A Bookworm

Buddy liked to read, and he was a very thoughtful person. He used to go to libraries just to study jazz-related material and music. Ever wonder how he had such a solid sense of music and the theory behind it? Besides practice, he soaked up literature that he could translate into ideas on his instrument. He studied approaches to music through books, not just listening. He used to read about Einstein, and astronomy too…those atomic particles on Emmons fretboards are a part of his character/signature because he was interested in them. He wanted to know more about many things, as any great inventor does. He gained inspiration not just by listening to music, but also by reading literature, which he translated into inspirational music on the pedal steel.

Buddy Emmons Music Thoery Books

Read more about things that interest you. How can they be applied to your instrument, or playing the pedal steel guitar? Also, be sure to read a music theory book once in a while…they’re not that boring if you relate it to pedal steel playing!

Have Hobbies/Interests

Buddy was interested in boxing, photography, physics, astronomy, music history, and much more. He related to these things personally, and he let these things impact him because they meant something to him. We can see and hear this impact through his pedal steel playing…he made notes punch you in the face like boxing gloves; and used his love of physics to help in the design of a signature fretboard.   Life is music, and music is life: if these are interchangeable, then why not let life’s influences on you show in your music.

Buddy Emmons - Einstein and Astrology Books

Try to think of something you are passionate about besides music and pedal steel, and see how you can apply it to your instrument and playing it. Do you enjoy restoring old cars? Then chances are you’d be great at restoring a vintage pedal steel. Do you enjoy playing golf? How can the physics and technique behind that sport relate to the technical aspects of playing the pedal steel guitar. Put a golf ball on your practice stand for inspiration and ideas.

Buddy was a star, a genius, and an icon to pedal steel players all over the world. He still is. Let’s let his character and human traits influence us to be better players. His playing was inspirational, and so was his spirited character. Keep on picking and smiling everyone!

Read more about Buddy Emmons below…

Buddy Emmons – Tonal Personality


Keep that Emmons mindset and practice…more tips and techniques here:     Practice Tips and Techniques

Left Foot Warmup Exercises

It can be very beneficial to warmup at the beginning of your playing or practice session.  Since the pedal steel is such a physical instrument, it is very similar to playing a sport in that it requires certain movements/exertions to achieve certain goals.

Warming up (stretches, exercises, drills, etc.) is almost standard for any sport, and for pedal steel playing it can be very helpful to do the same.  A basketball player may shoot some hoops from various positions on the court to warmup; a pedal steel player could work on various “shots” or “techniques” on their instrument to warmup too.

Pedal Steel Volume Technique

By focusing a little time on technique, a player can calibrate their playing by rehearsing certain movements and motions.  This can also help focus the mind for playing.  Here is a great exercise to warmup your left foot and pedal technique for playing sessions, while also building strong playing habits…

Spend 5-10 minutes on this warmup exercise.  It focuses on slow pedal movements to gain maximum control and precision with one’s left foot.  It will isolate the A, B, and C pedals, allowing one to work on these individual movements and foot positioning too.


Here’s how the exercise works:

If you engage the A pedal on the E9 neck, which raises our pitch two half steps on strings 5+10, and fret the bar at fret position 1, you have a D note on these strings. Now slowly disengage the pedal, while sliding up two frets and you have the same note since you disengaged the pedal and moved the bar up two half steps simultaneously. Since these are the same notes, if you gradually slide between these two positions (engaged 1st fret, disengaged 3rd fret) while gradually (dis)engaging the pedal, you shouldn’t hear a change in pitch. This is easier to do quickly!  But can you do it super slow, and avoid microtones?!!!

Here’s the trick:

If you do this process and move the bar real slowly from the 1st fret position (engaged pedal) up towards the 3rd fret position (disengaged pedal) – but only move the bar super slow, and you want to keep the pitch constant —  your foot will need to engage/disengage the pedal just as slow as the bar moves, until you reach your destination.  By doing these movements at a very slow speed, a player can really crystallize their foot technique and muscle memory, while strengthening the muscles used.

This exercise can also be effective in warming up with the B and C pedals…

  • For the B pedal – do the same process but use the 3rd string.  The 2nd fret position will have the pedal engaged, while the 3rd fret position will have it disengaged.
  • For the C pedal – do the same process but use the 4th string.  The 1st fret position will have the pedal engaged, while the 3rd fret position will have the pedal disengaged.  This movement is very similar to the A pedal’s warmup mentioned above.

This chart can help visually display these movements, and can be a great practice tool (click for larger view)…

LeftFootWarmupExercise1


Also, a great way to warmup the left foot and ankle is to work on “rocking” motions: a very important technique for using the A and B pedals simultaneously on the E9 neck.  I find the following movement to be very efficient in warming up the foot/ankle for this reason…

Starting with only the B pedal engaged, and using strings 5+6 at the fifth fret, pick this string grouping then slowly slide the bar up one fret while releasing the B pedal, and engaging the A pedal.  This will require the ankle to make a larger movement, by requiring it to rock towards the A pedal, and avoid engaging the B pedal once it arrives at the A pedal engaged position.

The following diagram (click for larger view) helps visually display this exercise/movement:

LeftFootWarmupExercise2

Notice how on the 6th string, our pitch will not change after the disengagement of the B pedal and the slide up one fret…just like the previous exercises.  A player should hear almost no change with this note, and try to avoid hearing microtones to keep it smooth.  The 5th string and A pedal movement will produce a change in pitch/note and should be audibly smooth as well.

This movement is challenging, but gives a player the capability of hitting the A pedal by itself, the B pedal by itself, and building the muscles commonly used for rocking on/off the A pedal with the B pedal engaged.  It is a move that can be found in Buddy Emmons’ “Blue Jade,” and can be used in many variations when playing pedal steel.


For more info related to the foot pedals, check these pages out…

Foot Pedals and Knee Levers

How the Pedals and Knee Levers Work

Metronome Ideas and Tricks

Having a strong foundation in rhythm can help a pedal steel player’s musicality. Using a metronome is one of the best ways to build a player’s rhythmic skills, and can go a long ways on and off the bandstand.

Here are some ideas and tips for practicing with a metronome…

-Speeds

Most of my practice with a metronome involves using it at a slow tempo. This allows me to really calibrate my attack on the strings with the beats of the metronome.  I am usually in the 55-75 BPM range, often in the 60’s.  By calibrating my attack, what I mean is I try to hear sonically if I’m slightly ahead of the beat, right on top of it, or playing behind it.

These three modes of attack can allow one to have more options rhythmically when playing with others. Playing ahead of the beat, without rushing it, can help drive certain parts of songs and give them more flare.  Playing on top of the beat is more common, and entails playing on time with the music surrounding you — you’ll be in time without accentuating the time too much and drawing attention away from the lyrics or song. Playing behind the beat can be fun too, and add more tail end to the percussive attacks of other instruments, without losing timing.  When doing this, your attack on the strings will very minutely follow the immediate sound of the beat.

WatchHands

-On 2+4

This is a good trick for working on your timing, and can help when learning jazz rhythms too.  Set your metronome real slow (I usually set it between 40 and 60 BPM).  Then allow the beats you hear on the metronome to act as beats 2 and 4 of the measure (4/4 meter), and beats 1 and 3 will be in between these and inaudible on the metronome.  Basically, you are using the metronome only for beats 2 and 4, while allowing your brain and mind to hear and interpret beats 1 and 3 on your own. When you do this, you’ll gain a deeper understanding of when the snare drum usually hits, and you’ll be able to accentuate beats 2 and 4 more within your playing. Having to fill in 1 and 3 on your own will give you practice and understanding of the function of these beats too.  After all, you are the one “making” these beats happen in your mind. For more practice ideas and exercises, switch it up: have the metronome only sound beats for 1 and 3, while you interpret 2 and 4 on your own.

ClockFace

-Get a good timbre

Finding a nice, pleasant sounding metronome is important for getting the most out of your practice. After all, who wants to continuously listen to a repeating noise that is annoying sounding It’s like playing with a drummer: it is much more enjoyable to play with one that sounds good, than one that doesn’t, ha!?

I recommend downloading multiple metronome apps that are free on your phone, then experimenting with them to see which one sounds best to you. Also, I recommend the app called DrumGenius. It has a great selection of drum loops in many music styles, which all sound great. It is a great way to practice rhythm, while adding a more realistic aspect to your session – with a good sound system it can feel like you are practicing with a drummer. This can really help when you get on the bandstand.

-Using with a drone

When practicing scales, intervals, arpeggios, etc. it is often very beneficial to have a drone track in the background. Try to use a metronome when practicing with a drone, as this will be beneficial in many ways: improving intonation, solidifying your timing, training your ears, making your practice more musical, etc. For more on practicing with a drone, check out these articles:

Practicing Music with Drones

Creating Your Own Drone Track


I hope these tips and ideas on using a metronome help players get more out of their practice time. Often, the best way to calibrate one’s timing on and off the instrument is to practice with a metronome.

For more practice ideas check out this page!!!